INTNUMInterval number: The nth sample database interval based on the start time specified in the Create Performance Data (CRTPFRDTA) command.PD (5,0)DTETIMInterval date (yymmdd) and time (hhmmss): The date and time of the sample interval.C (12)INTSECElapsed interval seconds: The number of seconds since the last sample interval.PD (7,0)IOPRNIOP resource name.C(10)MIIOPReservedC (1)MITYPEIOP type.C (4)MIPRCUProcessor utilization: The number of fixed-time intervals that this multifunction IOP spent in the idle state.PD (11,0)MIRAMUAvailable local storage (in bytes): The number of bytes of free local storage in the IOP. The free local storage will probably be non-contiguous because of fragmentation.PD (11,0)MITPKTTotal packets transferred.PD (11,0)MIKBYOTotal KB transmitted from an IOP to the system across the bus.PD (11,0)MIKBYITotal KB transmitted to the IOP from the system across the bus.PD (11,0)MIOPSROPSTART bus unit message received from another bus unit using normal flow.PD (11,0)MIOPSSOPSTART bus unit message received from another bus unit using reverse flow method 2 (always 0).PD (11,0)MISGLRSignals received.PD (11,0)MIOPSTOPSTARTs sent.PD (11,0)MISLGSSignals sent.PD (11,0)MIRSTQRestart queues sent.PD (11,0)MIRQDODMA requests sent for output of data: The number of requests the IOP sends to the system for data to be sent from the IOP to the system across the bus.PD (11,0)MIRQDIDMA requests sent for input of data: The number of requests the IOP sends to the system for data to be sent to the IOP from the system across the bus.PD (11,0)MIBNAROccurrences of BNA received.PD (11,0)MIIDLCIdle loop count (see notes): The number of times the primary IOP processor ran an idle loop. This is done when the IOP has no work to perform. This count is used with the idle loop time to calculate the primary IOP processor utilization in seconds.PD (11,0)MIIDLTIdle loop time (see notes): the time (in hundredths of microseconds) for the primary IOP processor to run the idle loop once. The value reported could be a multiple of the actual idle loop time. In that case, the value reported for the idle loop count is reduced by the same multiple so that the calculated IOP processor utilization is correctPD (11,0)MISYSFIOP system function time: Total processing unit time (in milliseconds) used by the IOP for basic system function that is running in the primary IOP processor.PD (11,0)MIDISKDisk time: Total processing unit time (in milliseconds) used by disk tasks that are running in the primary IOP processor.PD (11,0)MICOMMTotal communications time: Total processing unit time (in milliseconds) used by all the communications protocol tasks that are running in the primary IOP processor.PD (11,0)MISDLCSDLC communications time: Total processing unit time (in milliseconds) used by SDLC communications tasks that are running in the primary IOP processor.PD (11,0)MIASYNASYNC communications time: Total processing unit time (in milliseconds) used by asynchronous communications tasks that are running in the primary IOP processor.PD (11,0)MIBSCBSC communications time: Total processing unit time (in milliseconds) used by BSC communications tasks that are running in the primary IOP processor.PD (11,0)MIX25LX.25 LLC communications time: Total processing unit time (in milliseconds) used by X.25 LLC communications tasks that are running in the primary IOP processor.PD (11,0)MIX25PX.25 PLC communications time: Total processing unit time (in milliseconds) used by X.25 packet layer communications (PLC) tasks that are running in the primary IOP processor.PD (11,0)MIX25DX.25 DLC communications time: Total processing unit time (in milliseconds) used by X.25 data link control (DLC) and Point-to-Point Protocol (PPP) communications tasks that are running in the primary IOP processor.PD (11,0)MILANLAN communications time: Total processing unit time (in milliseconds) used by token-ring network, Ethernet, frame relay, fiber distributed data interface (FDDI), and asynchronous transfer mode (ATM) communications tasks. This includes processing time due to token-ring and Ethernet LAN emulation.PD (11,0)MISDLDSDLC short-hold mode time: Total processing unit time (in milliseconds) used by SDLC short-hold mode tasks that are running in the primary IOP processor.PD (11,0)MIRV02ISDN communications time: Total processing unit time (in milliseconds) used by ISDN LAPD, LAPE, and PMI communications tasks that are running in the primary IOP processor.PD (11,0)MIRV03ISDN communications time: Total processing unit time (in milliseconds) used by ISDN Q.931 communications tasks that are running in the primary IOP processor.PD (11,0)MISPService processor time: Total processing unit time (in milliseconds) used by the service processor function that is running in the primary IOP processor.PD (11,0)MIF1IDSubfunction 1 ID: The identifier for additional functions that may be running in the primary IOP processor.C (2)MIF1TMSubfunction 1 time: Total processing unit time (in milliseconds) used by the IOP function that is running in the primary IOP processorPD (11,0)MIF2IDSubfunction 2 ID: The identifier for additional functions that may be running in the primary IOP processor.C (2)MIF2TMSubfunction 2 time: Total processing unit time (in milliseconds) used by the IOP function that is running in the primary IOP processorPD (11,0)MIF3IDSubfunction 3 ID: The identifier for additional functions that may be running in the primary IOP processor.C (2)MIF3TMSubfunction 3 time: Total processing unit time (in milliseconds) used by the IOP function that is running in the primary IOP processor.PD (11,0)MIF4IDSubfunction 4 ID: The identifier for additional functions that may be running in the primary IOP processor.C(2)MIF4TMSubfunction 4 time: Total processing unit time (in milliseconds) used by the IOP function that is running in the primary IOP processor.PD (11,0)MIF5IDSubfunction 5 ID: The identifier for additional functions that are running in the primary IOP processor.C(2)MIF5TMSubfunction 5 time in milliseconds used by the IOP function that is running in the primary IOP processor.PD (11,0)MITWNXTotal processing unit time (in milliseconds) used by workstation and local twinaxial tasks that are running in the primary IOP processor.PD (11,0)MICPU2Processor 2 utilization: The utilization (in milliseconds) of the second IOP processor that handles specialized function. This field applies to Integrated xSeries^® Server (excluding I/O adapter versions) and is zero for other IOPs. Collection Services will not report values for Integrated xSeries Server.PD (11,0)MIADPReserved.PD (11,0)MIOTHOther function time: Total processing unit time (in milliseconds) used by other IOP functions that are running in the primary IOP processor. Other functions include those that cannot be reported in the subfunction 1-5 ID fields because all of the subfunction 1-5 ID fields are in use.PD (11,0)MIINTInterrupt level time: Total processing unit time (in milliseconds) used by interrupt level processing that is running in the primary IOP processor. This does not include interrupt level processing time that can be associated with a particular task.PD (11,0)MIRARemote access time: Total processing unit time (in milliseconds) used by the remote access tasks that are running in the primary IOP processor.PD (11,0)

Field Name	Description	Attribute